نیاز فوری به فایل overhead.awk و energy.awk

[mohandes]

سلام وقتتون بخیر...من برای انجام پروژم نیاز فوری به دو فایل awk overhead و مصرف انرژی دارم ممنون میشم فایلش رو در اینجا قرار بدید لطفا کمکم کنید.

[م ح ن]

##energy##


BEGIN {
initialenergy=1
maxenergy=0
n=60
nodeid=999
}
{
# Trace line format: energy
event = $1
time = $2
if (event == "r" || event == "d" || event == "s"|| event== "f") {
node_id = $9
energy = $17
}
if (event== "N") {
node_id = $5
energy = $7
}
# Store remaining energy
finalenergy[node_id] = energy
}
END {
# Compute consumed energy for each node
for (i in finalenergy) {
consumenergy[i] = initialenergy-finalenergy[i]
totalenergy += consumenergy[i]
if(maxenergy < consumenergy[i]){
maxenergy = consumenergy[i]
nodeid = i
}
}
###compute average energy
averagenergy=totalenergy/n
####output
for (i=0; i<n; i++) {
print("consumed energy for node",i, consumenergy[i])
}
print("+===========+")
print("average energy consumption",averagenergy)
print("+===========+")
print("total energy",totalenergy)
}

[م ح ن]

##overhead
BEGIN {
send = 0;
recv = 0;
bytes = 0;
st = 0;
ft = 0;
rtr = 0;
delay = 0;
aodv_ = 0;
last_pkt_recv=0;
jitter=0;
j_count=0;
nodes=0;
}

{

if ( $16 == &quot;-Ne&quot; )
{
if (initial_energy[$9] == &quot;&quot
initial_energy[$9] = $17;
energy[$9] = $17;
if(nodes < $9)
nodes = $9;
}

if ( $19 == &quot;RTR&quot; && $1 == &quot;s&quot; && $35 != &quot;cbr&quot; && $35 != &quot;udp&quot; && $35 != &quot;ack&quot
rtr++;

if ( $19 == &quot;AGT&quot; && $1 == &quot;s&quot
{
if(send == 0)
st = $3;
ft = $3;
st_time[$41] = $3;
send++;
}

if ( $19 == &quot;AGT&quot; && $1 == &quot;r&quot
{
if(recv == 0)
{
last_pkt_recv = $3;
}
else
{
jitter+=$3 - last_pkt_recv;
j_count++;
last_pkt_recv = $3
}
recv++;
bytes+=$37
ft_time[$41] = $3;
delay += ft_time[$41]-st_time[$41]
}

}

END {
total_energy = 0;
residual=0;
for (i=0;i<nodes;i++) {
residual_energy[i] = initial_energy[i] - energy[i];
total_energy+=residual_energy[i];
residual+=energy[i];
}


print &quot;No of pkts send \t\t&quot; send
print &quot;No of pkts recv \t\t&quot; recv
print &quot;Pkt_delivery_ratio: \t\t&quot; recv/send*100
print &quot;Control_overhead: \t\t&quot; rtr
print &quot;Normalized_routing_overheads: \t&quot; rtr / recv
print &quot;Delay: \t\t\t\t&quot; delay/recv
print &quot;Throughput: \t\t\t&quot; bytes*8/(ft-st)
print &quot;Jitter: \t\t\t&quot; jitter/j_count
print &quot;No of Pkts Dropped \t\t&quot; send-recv
print &quot;Dropping_Ratio: \t\t&quot; (send-recv)/send*100
print &quot;Total_Energy_Consumption: \t&quot; total_energy
print &quot;Avg_Energy_Consumption: \t&quot; total_energy/nodes
print &quot;Overall Residual Energy: \t&quot; residual
print &quot;Avg Residual Energy: \t\t&quot; residual/nodes
}